Vintage Ply manufactures IS:1659 grade block boards at its Fatehpur plant, with a solid seasoned softwood core bonded under BWP grade resin for high screw holding and stability, and supplies dealers, furniture makers and contractors across Madhya Pradesh with full load and part load dispatch.
Block board is the panel furniture makers reach for when a flush door, table top or wardrobe shutter has to span a long width without sagging or warping. Instead of layered veneers alone, it is built around a core of seasoned softwood battens, which gives it screw and hinge holding strength that thin plywood cannot match. Vintage Ply manufactures IS:1659 BWP grade block boards with zero gap core composing, hardwood face veneers and vacuum pressure preservative treatment.
Every sheet is produced at our Fatehpur factory through a controlled 15 step process and checked for screw holding strength, bending strength, moisture content and thickness tolerance before it leaves the plant. Furniture makers, dealers, interior contractors and turnkey builders across Madhya Pradesh buy direct from the manufacturer, which keeps rates transparent and supply consistent.
From furniture workshops in Indore to flush door and wardrobe fit outs in Bhopal apartments.
Solid, stable panels for internal and external door shutters where screw and hinge holding strength matters over years of daily use.
Tall wardrobe panels and sliding shutters across Madhya Pradesh homes that need to stay flat and true without sagging.
Study tables, office desks and conference table tops where long unsupported spans need to resist bending under load.
Decorative wall panelling and office partitions across Bhopal, Indore and Gwalior commercial interiors.
Base units and carcasses for modular kitchens and furniture across the state that need to hold hardware securely for years.
Long span ceiling and structural panelling work where plywood alone would flex or need extra framing support.
| Supply Region | All Madhya Pradesh Districts |
|---|---|
| Core Material | Seasoned Softwood Battens |
| Bonding | BWP Grade Phenol Formaldehyde Resin |
| Moisture Content | 8% - 12% |
| Available Thickness | 12mm, 16mm, 19mm & 25mm |
| Standard Sizes | 8x4, 8x3, 7x4, 7x3 ft |
| Treatment | Vacuum Pressure Preservative |
| Screw Holding Test | High Withdrawal Resistance, No Splitting |
| Certification | IS:1659 BWP Grade |
Solid softwood battens give hinges, screws and hardware a firm grip that thin plywood cores cannot match on wardrobe shutters and flush doors.
Zero gap core composing keeps table tops and long door shutters flat under load, without the sag ordinary panels develop over time.
Vacuum pressure treated veneers guard against termites, borers and fungus, a real risk in older Madhya Pradesh buildings and ground floor installations.
Dealers get the same grade, shade and thickness on every reorder, which matters when a project runs across several months and multiple sites.
Four reasons buyers in Bhopal, Indore, Jabalpur and across Madhya Pradesh move their block board orders to a direct manufacturer instead of a trading house.
Orders ship straight from our own Fatehpur plant, so you pay manufacturer rates and get one point of accountability for quality and timelines.
Each production batch is tested for screw holding strength, bending strength, moisture content and thickness before it is packed for dispatch.
Vintage Ply panels carry a written guarantee against termite attack, borer damage and fungal decay for the warranty period stated on the sheet.
Full truck loads for dealers and part loads for project sites reach Madhya Pradesh destinations with packing that protects edges in transit.
What each test measures and what it means for the door, wardrobe or table top built from that panel.
| Quality Check | What We Test | Our Benchmark | What It Means on Site |
|---|---|---|---|
| Screw Holding Strength | Withdrawal resistance of the core battens | Tested against IS:1659 norms | Hinges and hardware stay fixed on wardrobe shutters and doors without loosening. |
| Bending Strength | Load bearing capacity across the span | Tested dry and after conditioning | Table tops and long door shutters stay flat instead of sagging under load. |
| Moisture Content | Water held inside the finished panel | Maintained between 8% and 12% | Panels do not swell in the rains or shrink in dry heat, so joints stay tight. |
| Thickness Tolerance | Uniformity across the full sheet | Calibrated and wide belt sanded | Doors and cabinetry line up without extra carpenter or fabricator correction. |
| Preservative Retention | Chemical held inside the core and veneer | Vacuum pressure impregnated | Termite and borer protection stays intact even where the sheet has been cut. |
| Core Gap Inspection | Hollow pockets inside the core | Zero gap core composing | Screws, fittings and hardware hold firmly under daily use and vibration. |
Test details for a specific batch can be shared with the quotation for block board supplies in Madhya Pradesh.
The checks that decide whether a block board brand gets specified on a project in Bhopal, Indore or across Madhya Pradesh.
BWP grade phenol formaldehyde resin holds the battens and veneers together through the screw withdrawal and bending tests real furniture and doors are actually put through.
Zero gap core composing with no hollow pockets, so fittings and hardware hold firmly and the panel carries load without sagging over the years.
Preservative is driven through the core and veneer under vacuum pressure rather than brushed on the surface, so protection stays even after cutting.
Wide belt sanding and calibration keep thickness uniform across the sheet, which saves fabrication time on flush door and cabinetry alignment.
Every sheet carries printed branding and a duplicate proof QR code, so a Madhya Pradesh buyer can confirm the panel is genuine Vintage Ply.
Buying direct removes the trading margin, which matters on bulk project quantities for builders and large interior contractors.
Vintage Ply dispatches block boards to dealers, furniture makers and project sites in these Madhya Pradesh cities and the districts around them.
Not listed above? We appoint dealers in open districts and still deliver project quantities anywhere in Madhya Pradesh. Talk to our team.
Answers to what furniture makers, dealers and contractors ask us most often before placing a first order.
Vintage Ply is a manufacturer, not a trading brand. All block boards are produced at our own plant at B-29-30, UPSIDC Industrial Area, Malwan, Fatehpur, Uttar Pradesh, and dispatched to Madhya Pradesh from there.
Block board has a core of seasoned softwood battens sandwiched between veneers, which gives it high screw and hinge holding strength for large panels like flush doors and table tops. Plywood is built from multiple cross bonded veneer layers, which gives more uniform strength and better moisture resistance for structural and wet area use.
Standard thicknesses are 12mm, 16mm, 19mm and 25mm in sheet sizes of 8x4, 8x3, 7x4 and 7x3 feet. Other sizes can be discussed for project quantities before production is scheduled.
Yes. Our block boards are manufactured to IS:1659 BWP grade with a zero gap softwood core, which is what a flush door, wardrobe shutter or table top needs for high screw holding and resistance to warping under daily use.
Dispatch timelines depend on order size and current production schedule. Full truck loads for dealers and part loads for project sites are both accepted, and our team confirms a dispatch date in writing when the order is booked.
Every sheet carries printed branding and a duplicate proof QR code applied at the final stage of production. Scanning the code confirms the panel came from our plant, which protects buyers from counterfeit stock in the market.
Yes. Vintage Ply block boards carry a written guarantee against termite attack, borer damage and fungal decay for the warranty period stated on the sheet and in the invoice documentation.
We appoint stocking dealers and distributors in districts that are currently open. Dealers get territory backing, display support and priority dispatch. Share your city and current business profile and our team will confirm availability.
Call +91 73079 47592, message us on WhatsApp or send your requirement to info@vintageply.com with the grade, thickness, size and quantity. Rates are shared directly by the manufacturer with no trading margin in between.
Send us your thickness and quantity requirement. Our team shares manufacturer rates, sample boards and a confirmed dispatch plan for your workshop, site or showroom.
