Vintage Ply manufactures IS:2202 (Part 1) grade solid core flush doors at its Fatehpur plant, built on a block board core bonded under BWP grade resin for high hinge and lock holding, and supplies dealers, builders and contractors across Andhra Pradesh with full load and part load dispatch.
A flush door is only as good as the core inside it, which is why Vintage Ply builds its doors on a solid block board core instead of a hollow or particle board filling. The seasoned softwood battens give hinges, locks and door closers a firm grip that a thin core cannot match, while the outer faces are finished in veneer or laminate as per design. We manufacture IS:2202 (Part 1) BWP grade solid core doors in both a waterproof design finish for bathrooms and wet areas, and a commercial plain finish for offices and painted interiors.
Every door is produced at our Fatehpur factory through a controlled 15 step process and checked for hinge and lock holding strength, squareness, moisture content and thickness tolerance before it leaves the plant. Dealers, builders, interior contractors and turnkey project teams across Andhra Pradesh buy direct from the manufacturer, which keeps rates transparent and supply consistent.
From main entrance doors in Vijayawada bungalows to bathroom and office doors in Visakhapatnam apartments.
Solid, heavy duty shutters that hold multi point locks and closers firmly for main doors that see daily traffic and full weather exposure.
Lightweight yet stable commercial plain doors finished in veneer or laminate for bedrooms and internal passages across Andhra Pradesh homes.
Waterproof design doors that resist swelling and delamination where moisture and daily washdowns would damage an ordinary panel door.
Plain and laminate finished doors for office cabins, retail fit outs and commercial interiors across Visakhapatnam, Vijayawada and Guntur.
Guest room and service area doors that hold up to heavy footfall while staying flat and square in the frame for years.
Bulk door supply for residential towers and turnkey interior contractors who need the same grade and finish consistently across every unit.
| Supply Region | All Andhra Pradesh Districts |
|---|---|
| Core Material | Solid Block Board Core (Seasoned Softwood Battens) |
| Bonding | BWP Grade Phenol Formaldehyde Resin |
| Moisture Content | 8% - 12% |
| Available Thickness | 30mm, 32mm & 35mm |
| Standard Sizes | 6'x2'6", 6'6"x2'9", 6'6"x3', 7'x3' (custom sizes on request) |
| Door Types | Waterproof Design & Commercial Plain |
| Treatment | Vacuum Pressure Preservative |
| Hinge & Lock Holding Test | High Withdrawal Resistance, No Splitting |
| Certification | IS:2202 (Part 1) BWP Grade |
Solid softwood battens give hinges, locks and closers a firm grip that a hollow or particle board core cannot match on main and interior doors.
Zero gap core composing keeps door shutters flat and square in the frame, and the waterproof design range resists swelling in bathrooms and wet areas.
Vacuum pressure treated veneers guard against termites, borers and fungus, a real risk in older Andhra Pradesh buildings and ground floor installations.
Dealers get the same grade, finish and thickness on every reorder, which matters when a project runs across several months and multiple sites.
Four reasons buyers in Visakhapatnam, Vijayawada, Guntur and across Andhra Pradesh move their door orders to a direct manufacturer instead of a trading house.
Orders ship straight from our own Fatehpur plant, so you pay manufacturer rates and get one point of accountability for quality and timelines.
Each production batch is tested for hinge and lock holding strength, squareness, moisture content and thickness before it is packed for dispatch.
Vintage Ply doors carry a written guarantee against termite attack, borer damage and fungal decay for the warranty period stated on the invoice.
Full truck loads for dealers and part loads for project sites reach Andhra Pradesh destinations with edge protection packing built for door shutters.
What each test measures and what it means for the door shutter installed at your site.
| Quality Check | What We Test | Our Benchmark | What It Means on Site |
|---|---|---|---|
| Hinge and Lock Holding Strength | Withdrawal resistance of the core battens | Tested against IS:2202 norms | Hinges, locks and closers stay fixed on the shutter without loosening over time. |
| Squareness and Warp Check | Straightness of all four edges | Tested dry and after conditioning | Door shutters sit flush in the frame and close without binding or gaps. |
| Moisture Content | Water held inside the finished door | Maintained between 8% and 12% | Doors do not swell in the rains or shrink in dry heat, so they keep closing smoothly. |
| Thickness Tolerance | Uniformity across the full shutter | Calibrated and wide belt sanded | Doors line up in the frame without extra carpenter correction on site. |
| Preservative Retention | Chemical held inside the core and veneer | Vacuum pressure impregnated | Termite and borer protection stays intact even at cut edges and lock mortises. |
| Core Gap Inspection | Hollow pockets inside the core | Zero gap core composing | Hinges, locks and hardware hold firmly under daily opening and closing. |
Test details for a specific batch can be shared with the quotation for door supplies in Andhra Pradesh.
The checks that decide whether a door brand gets specified on a project in Visakhapatnam, Vijayawada or across Andhra Pradesh.
BWP grade phenol formaldehyde resin holds the battens and veneers together through the hinge withdrawal and warp tests real doors are actually put through.
Zero gap core composing with no hollow pockets, so hinges and hardware hold firmly and the shutter stays flat without sagging over the years.
Preservative is driven through the core and veneer under vacuum pressure rather than brushed on the surface, so protection stays even at cut edges and mortises.
Wide belt sanding and squaring keep every edge true, which saves fabrication time on frame fitting and hardware alignment.
Every door carries printed branding and a duplicate proof QR code, so a Andhra Pradesh buyer can confirm the shutter is genuine Vintage Ply.
Buying direct removes the trading margin, which matters on bulk project quantities for builders and large interior contractors.
Vintage Ply dispatches doors to dealers, builders and project sites in these Andhra Pradesh cities and the districts around them.
Not listed above? We appoint dealers in open districts and still deliver project quantities anywhere in Andhra Pradesh. Talk to our team.
Answers to what builders, dealers and contractors ask us most often before placing a first order.
Vintage Ply is a manufacturer, not a trading brand. All doors are produced at our own plant at B-29-30, UPSIDC Industrial Area, Malwan, Fatehpur, Uttar Pradesh, and dispatched to Andhra Pradesh from there.
Both are built on the same solid block board core and BWP grade bonding. The waterproof design door has a moulded, water resistant face finish suited to bathrooms and wet areas, while the commercial plain door is a flat, paintable face meant for painted or laminated interior use.
Standard thicknesses are 30mm, 32mm and 35mm in commonly used door sizes. Custom heights and widths can be discussed for project quantities before production is scheduled.
Yes. Our waterproof design doors are manufactured to IS:2202 (Part 1) BWP grade with a zero gap block board core, which is what a bathroom or wet area door needs for resistance to swelling and delamination under daily moisture exposure.
Dispatch timelines depend on order size and current production schedule. Full truck loads for dealers and part loads for project sites are both accepted, and our team confirms a dispatch date in writing when the order is booked.
Every door carries printed branding and a duplicate proof QR code applied at the final stage of production. Scanning the code confirms the shutter came from our plant, which protects buyers from counterfeit stock in the market.
Yes. Vintage Ply doors carry a written guarantee against termite attack, borer damage and fungal decay for the warranty period stated on the invoice documentation.
We appoint stocking dealers and distributors in districts that are currently open. Dealers get territory backing, display support and priority dispatch. Share your city and current business profile and our team will confirm availability.
Call +91 73079 47592, message us on WhatsApp or send your requirement to info@vintageply.com with the door type, thickness, size and quantity. Rates are shared directly by the manufacturer with no trading margin in between.
Send us your door type, thickness and quantity requirement. Our team shares manufacturer rates, sample doors and a confirmed dispatch plan for your site, dealership or project.
