Vintage Ply manufactures IS:710 grade marine plywood at its Fatehpur plant, bonded with undiluted phenol formaldehyde resin for continuous water exposure, and supplies dealers, boat builders and contractors across Maharashtra with full load and part load dispatch.
Marine plywood carries the highest boiling waterproof rating in the IS classification system, and Maharashtra gives it plenty to prove. Coastal humidity along Mumbai, Thane and the Konkan belt, plus direct water contact on boats, docks and wet area interiors, attacks weak bonding fast. Vintage Ply manufactures IS:710 marine grade plywood with hardwood core veneers, undiluted phenol formaldehyde resin and vacuum pressure preservative treatment.
Every sheet is produced at our Fatehpur factory through a controlled 15 step process and checked for bonding strength, moisture content, thickness tolerance and boiling water resistance before it leaves the plant. Boat builders, dealers, interior contractors and turnkey builders across Maharashtra buy direct from the manufacturer, which keeps rates transparent and supply consistent.
From boat yards on the Konkan coast to wet area interiors in Mumbai and Pune apartments.
Hulls, decks and interior fit outs for boat builders along the Konkan coast and Mumbai harbour where continuous water contact is unavoidable.
Decking, fenders and structural panelling for port and waterfront infrastructure across Maharashtra's coastline.
Vanity units, shower cladding and utility area cabinetry that sit in direct and repeated contact with water.
Base cabinets and sink units for kitchens in Mumbai, Thane and the Konkan belt where ordinary BWR plywood swells and fails.
Formwork, decking and poolside furniture for resorts and residential complexes with pools across the state.
Weather exposed cladding, pergolas and outdoor furniture that need bonding strength ordinary plywood cannot hold under rain.
| Supply Region | All Maharashtra Districts |
|---|---|
| Core Material | Selected Hardwood Core |
| Bonding | Undiluted Phenol Formaldehyde Resin |
| Moisture Content | 8% - 12% |
| Available Thickness | 6mm, 9mm, 12mm, 16mm & 19mm |
| Standard Sizes | 8x4, 8x3, 7x4, 7x3 ft |
| Treatment | Vacuum Pressure Preservative |
| Boiling Water Test | 72 Hour Immersion, No Delamination |
| Certification | IS:710 Marine Grade |
Panels hold their bond after prolonged boiling water immersion, which is the standard boat hulls, docks and wet area cabinetry are actually exposed to.
Zero gap hardwood core and undiluted resin keep veneer layers bonded under the flexing and soaking that ordinary BWR plywood cannot take.
Vacuum pressure treated veneers guard against termites, borers and fungus, a real risk in older Maharashtra buildings and ground floor installations.
Dealers get the same grade, shade and thickness on every reorder, which matters when a project runs across several months and multiple sites.
Four reasons buyers in Mumbai, Pune, Nashik and along the Konkan coast move their marine plywood orders to a direct manufacturer instead of a trading house.
Orders ship straight from our own Fatehpur plant, so you pay manufacturer rates and get one point of accountability for quality and timelines.
Each production batch is tested for glue shear strength, boiling water resistance, moisture content and thickness before it is packed for dispatch.
Vintage Ply panels carry a written guarantee against termite attack, borer damage and fungal decay for the warranty period stated on the sheet.
Full truck loads for dealers and part loads for project sites reach Maharashtra destinations with packing that protects edges in transit.
What each test measures and what it means for the boat, dock or wet area unit built from that panel.
| Quality Check | What We Test | Our Benchmark | What It Means on Site |
|---|---|---|---|
| Glue Shear Strength | Bond strength between veneer layers | Tested dry and after water immersion | Layers stay bonded, so the panel does not separate at the edges under continuous water exposure. |
| Boiling Water Resistance | Bond behaviour after prolonged boiling | 72 hour immersion, no delamination | Safe for boat hulls, docks, bathroom vanities and coastal Maharashtra wet areas. |
| Moisture Content | Water held inside the finished panel | Maintained between 8% and 12% | Panels do not swell in the rains or shrink in dry heat, so joints stay tight. |
| Thickness Tolerance | Uniformity across the full sheet | Calibrated and wide belt sanded | Hulls and cabinetry line up without extra carpenter or fabricator correction. |
| Preservative Retention | Chemical held inside the veneer | Vacuum pressure impregnated | Termite and borer protection stays intact even where the sheet has been cut. |
| Core Gap Inspection | Hollow pockets inside the core | Zero gap core composing | Screws, fittings and hardware hold firmly under load and vibration. |
Test details for a specific batch can be shared with the quotation for marine plywood supplies in Maharashtra.
The checks that decide whether a marine plywood brand gets specified on a project in Mumbai, Pune or along the Konkan coast.
Undiluted phenol formaldehyde resin holds the veneers together through the boiling water test and the continuous soaking a boat hull or dock panel actually faces.
Zero gap core composing with no hollow pockets, so fittings and hardware hold firmly and the panel carries load without sagging over the years.
Preservative is driven through the veneer under vacuum pressure rather than brushed on the surface, so protection stays even after cutting.
Wide belt sanding and calibration keep thickness uniform across the sheet, which saves fabrication time on hull curvature and cabinetry alignment.
Every sheet carries printed branding and a duplicate proof QR code, so a Maharashtra buyer can confirm the panel is genuine Vintage Ply.
Buying direct removes the trading margin, which matters on bulk project quantities for builders and large interior contractors.
Vintage Ply dispatches marine plywood to dealers, boat builders and project sites in these Maharashtra cities and the districts around them.
Not listed above? We appoint dealers in open districts and still deliver project quantities anywhere in Maharashtra. Talk to our team.
Answers to what boat builders, dealers and contractors ask us most often before placing a first order.
Vintage Ply is a manufacturer, not a trading brand. All marine plywood is produced at our own plant at B-29-30, UPSIDC Industrial Area, Malwan, Fatehpur, Uttar Pradesh, and dispatched to Maharashtra from there.
Both grades share the same undiluted phenol formaldehyde resin bonding. Marine grade is manufactured to IS:710 with a zero gap hardwood core for continuous water contact such as boat hulls and docks, while BWP plywood is intended for kitchen and bathroom units that see repeated but not constant exposure.
Standard thicknesses are 6mm, 9mm, 12mm, 16mm and 19mm in sheet sizes of 8x4, 8x3, 7x4 and 7x3 feet. Other sizes can be discussed for project quantities before production is scheduled.
Yes. Our marine grade is bonded with undiluted phenol formaldehyde resin and tested for bond strength after 72 hours of boiling water immersion, which is what a boat hull, dock panel or waterfront structure needs to hold up without delamination.
Dispatch timelines depend on order size and current production schedule. Full truck loads for dealers and part loads for project sites are both accepted, and our team confirms a dispatch date in writing when the order is booked.
Every sheet carries printed branding and a duplicate proof QR code applied at the final stage of production. Scanning the code confirms the panel came from our plant, which protects buyers from counterfeit stock in the market.
Yes. Vintage Ply marine plywood carries a written guarantee against termite attack, borer damage and fungal decay for the warranty period stated on the sheet and in the invoice documentation.
We appoint stocking dealers and distributors in districts that are currently open. Dealers get territory backing, display support and priority dispatch. Share your city and current business profile and our team will confirm availability.
Call +91 73079 47592, message us on WhatsApp or send your requirement to info@vintageply.com with the grade, thickness, size and quantity. Rates are shared directly by the manufacturer with no trading margin in between.
Send us your thickness and quantity requirement. Our team shares manufacturer rates, sample boards and a confirmed dispatch plan for your boat yard, site or showroom.
